How to Reset/Relearn 4Runner TPMS Light

4 jogger 2004-2007 TPMS Reset

TPMS RESET – PROCEDURE

NOTE: Initialization is NOT forced if re-inflating tires come the at this time specified tires pressure.

You are watching: Toyota 4runner tire pressure sensor blinking

NOTE: The device will should be initialized once tires room rotated; tires are replaced with tires of various pressures; tire pressure sensor and/or tire pressure monitor ECU are replaced. Collection tire pressure within the specified selection before initializing. View Initializing Tire press Monitor System. When a tire pressure sensor and/or tire press monitor ECU space replaced, the sensor ID must be memorized through the tire press monitor ECU former to mechanism initialization. Watch Tire push Sensor Registration.

Tire press Monitor Warning Light

NOTE: The tire press warning light may turn on as result of natural reasons such as natural air leaks or tires pressure changes caused through temperature. In this case, adjusting the tire pressure will revolve off the warning light.When the tire press warning irradiate does not go off, or once it come on throughout driving, inspect tire push (including spare tire) and change as necessary. The warning light must turn turn off after a couple of minutes. If the warning light is quiet on even though the tire pressure is appropriately adjusted, the tire might be punctured. Repair as necessary. If the warning light is quiet on or blinks, there is a malfunction in the TPM system. See suitable manufacturer business information.

Under the following conditions, the system might not duty properly:

The areas, infrastructure or devices that use comparable radio tide frequencies are situated in the vicinity that the vehicle.A radio maker of similar frequency is used in or close to the vehicle. Together A many snow or ice is grounding to the vehicle, especially the wheels and around the wheel houses.The battery of the sensor has actually been depleted. L A tires without tire press monitor valve sub-assembly is used. Tires chains room used.If any kind of other wheels than the stated ones room used, the system may not duty properly because the radio waves are in different ways transmitted indigenous the tire push sensor.Depending top top the tires type, the system might not duty properly even though the mentioned wheels space used.

Initializing Tire press Monitor System

NOTE: The system will have to be initialized as soon as tires room rotated; tires are replaced with tires of different pressures; tire pressure sensor and/or tire pressure monitor ECU are replaced; or when a brand-new vehicle is delivered. Collection tire press within the specified variety before initializing.

NOTE: as soon as initializing the system, the existing tire problem is stored as a standard.


During initialization, the tire push monitor valve sub-assembly procedures the inflation press of the tires, and also registers the signals that are transmitted right into the tire push monitor ECU at a frequency of one every 3 minutes. The initialization procedure is completed once the signals from the 5 tires have been received.

1. Collection the tire pressure of every wheels (including preventive tire) to push specified top top the tire and loading info label.2. V the auto stopped and parking brake applied, turn the ignition switch to the ~ above position.3. Press and hold the tire push warning reset switch until the tire pressure warning lamp blinks 3 time at one-second intervals.4. Confirm that initialization is complete using the hand-held tester. First select “DATA LIST” on the handheld tester, climate verify the the “TIREPRESS” values are displayed. It may take 5 come 6 minutes because that the “TIREPRESS” worths to display on the hand-held tester screen

NOTE: The initialization procedure takes 5 to 6 minutes to it is in completed. The initialization process can it is in terminated by connecting terminals 4 (TC) and 13 (CG) that the DLC3.

Tire pressure Sensor Registration

NOTE: If the tire push sensor and/or tire push monitor ECU space replaced, the transmitter ID demands to it is in registered in the tire push monitor ECU former to device initialization. To do this procedure, the Toyota hand-held tester should be used.

Register Transmitter ID

1. Set the tire push of all wheels (including spare tire) to pressure specified ~ above the tire and loading details label.2. Connect the hand-held tester come DLC3.3. Turn ignition move to ~ above position.4. Choose the “REGIST TIRE” mode. See Fig. 14 and also Fig. 20 .

*
*
5. Input the transmitter IDs (ID1 to ID5) making use of the hand-held tester and also transmit it come the tire press monitor ECU.6. Collection the id transmission condition to “SUCCEEDED”.

NOTE: If actions 4-6 space not completed in ~ 5 minutes, the mode will go back to the normal operation mode.

Confirmation the Transmitter i would Registration

1. Collection the tire push of every wheels (including preventive tire) to the specified value.2. Affix the hand-held tester to DLC3.3. Revolve ignition switch to ~ above position.4. Pick “DATA LIST” setting on the hand-held tester.5. Check the “TIREPRESS” worths are presented on the hand-held tester screen.

4 jogger 2008-2014 TPMS Reset

TPMS RESET – PROCEDURE

NOTE: Reset is NOT required if re-inflating tires to the currently specified tires pressure.

NOTE: once a tire press sensor and/or tire press monitor ECU space replaced, the sensor ID have to be memorized by the tire press monitor ECU. View Tire

Pressure Sensor Registration.


NOTE: If the negative battery terminal is disconnected, initialize the following system ~ the terminal is reconnected: Power window Control System. Describe owner’s hands-on or appropriate manufacturer business information.

Tire press Monitor Warning Light

When the tire push warning light does no go off, or once it come on during driving, inspect tire pressure and adjust as necessary. The warning light need to turn turn off within a couple of minutes. If the warning irradiate is quiet on also though the tire pressure is correctly adjusted, the tire can be punctured. Repair together necessary. If the warning light turns on in ~ several hrs after adjusting the tires pressure, the tires may have a slow-moving air leak. If the warning irradiate is quiet on or blinks, over there is a malfunction in the TPM system. See suitable manufacturer service information.

NOTE: The tire press warning light may turn on as result of natural causes such as natural air leaks or tires pressure alters caused by temperature. In this case, adjusting the tire press will turn off the warning light. Under the complying with conditions, the system might not role properly:

Facilities or gadgets that use similar radio wave frequencies are situated in the vicinity that the vehicle.A radio an equipment of similar frequency is used close to the vehicle.A lot of snow or ice cream is stuck to the vehicle, especially approximately the wheel or wheel housings.Tires and wheels are set up that space not equipped through a tire pressure sensor.Snow tires or tires chains space used. Together The battery the the sensor has actually been depleted.Wheels various other than manufacturer manufacturing facility wheels space used. If any other wheels 보다 the mentioned ones are used, the system may not duty properly due to the fact that the radio waves are in different ways transmitted indigenous the tire pressure sensor.Depending ~ above the tire type, the system might not role properly even though the stated wheels room used. L utilizing a different kind of tires in mix with actual tires.

Tire push Sensor Registration

NOTE: when a tire press sensor and/or tire press monitor ECU are replaced, the sensor ID need to be memorized through the tire push monitor ECU. To do this procedure, a Toyota Techstream need to be used. That is not essential to it is registered the sensor ID(s) once only tires rotation is performed.

NOTE: prior to beginning registration procedure on vehicles whereby tire pressure sensors have not been replaced, retrieve sensor transmitter ID(s) utilizing intelligent tester or by analysis the i would on the tire press sensor. If sensor is being replaced with a brand-new one, make a keep in mind of the transmitter ID before installation, together it cannot be seen after sensor is installed. Check out Fig. 21.

*

1. Set the tire push of every wheels to push specified top top the tire and loading information label.2. Connect the smart tester to DLC3. See Fig. 11.

*
3. Turn the Tachstream scan tool on and also the ignition move to on position.4. Go into the complying with menus: Chassis / Tire push Monitor / utility / i would Registration.5. Perform the procedure shown on the scan tool.NOTE: Tire pressure sensor IDs the were previously registered will be deleted from the memory once registration is completed.6. Check the tire press sensor’s IDs space registered:7. Get in the adhering to menus: Chassis / Tire pressure Monitor / Data List.8. Check the tire push values are displayed for every 4 tires.

NOTE: It might take approximately 2 or 3 minute to update the tire press data. If tire pressure values carry out not display screen after 2 or 3 minutes, troubleshoot DTCs C2121/21 come C2124/24 (on some models, up to C2125/25).

See more: Which Term Is Used To Describe Aiming Too High For A Particular Goal ?


NOTE: If the ID(s) have actually not to be registered, DTC C2171/71 is set in the tire press monitor ECU after ~ 3 minutes or more.