Has your rotate signal switch begun to work-related just intermittently, all the time, or not at all? This article will certainly walk you through the procedure of replacing it via a new one.

You are watching: How to replace multifunction switch on ford f150


This write-up uses to the Ford F-150.

Turn signals are something that a lot of folks do not even bvarious other to use these days, yet if you"re analysis this, you are most likely among the excellent motorists that does. The trouble via rotate signals is that they, like every other mechanical/electric part on your auto, will certainly more than likely go bad inevitably. The telltale signs of a bad rotate signal switch include one that works just intermittently, not at all, or (the worst) will not revolve off. If any of these troubles sound familiar, keep reading and also we"ll walk you through the procedure of replacing your turn signal switch.

*

Materials NeededNew turn signal switchRatchet8mm and also 7/32" socketPickFlat head screwdriver8mm wrench2 jaw pullerT50 Torx bit

Step 1 – Disconnect battery and also fuse

Loosen up your battery cables through an 8mm socket and also ratchet, then disattach the battery.Use a level head screwdriver to pry the terminals cost-free if they are corroded.On the passenger side, underneath the glove box, pull the side panel out to access the fusage box.Use a flat head screwdriver to pry down on the tab of the fuse box cover and remove it.Use the fuse puller in the cover to pull the red 10 amp fuse (3rd one in on height row, check out Figure 3).
*
Figure 1. Rerelocate the passenger side kick panel cover.
*
Figure 2. Rerelocate the fuse box cover.
*
Figure 3. Rerelocate the fusage displayed.

Tip 2 – Remove the steering wheel

Use a flat head screwdriver to pry off the circular plastic cover on the right-hand also side of the steering column.Remove the 8mm bolt inside the hole.
*
Figure 4. Pry off the circular covers on each side of the steering wheel.
*
Figure 5. Remove the bolts inside each cover.Repeat the steps on the driver"s side, then pull the center percent of the steering wheel out.Disattach the peak harness inside the steering wheel by pushing down on the red tab through a level head screwdriver.Disaffix the bottom tab by prying out the gray clip via a pick, the pry out on the tab at the peak.
*
Figure 6. Pull out the center/horn of the wheel.
*
Figure 7. Disattach the two harnesses connected to the horn.Install a two jaw puller in the facility of the steering wheel and tighten it till the steering wheel comes loose and you are able to pull it off.Turn the steering wheel till it clicks right into place, then rerelocate the T50 bolt in the facility of the steering wheel.Rerelocate the 7/32" bolt underneath the steering wheel.
*
Figure 8. Remove the bolt from the bottom of the steering column.
*
Figure 9. Rerelocate the bolt from the center of the wheel.
*
Figure 10. Use a 2 jaw puller to rerelocate the steering wheel.

Tip 3 – Rerelocate rotate signal switch

Pull dvery own on the steering wheel adjustment level and also pull dvery own on the bottom trim item of the column to remove it.
*
Figure 11. Pull down on the bottom cover to remove it.Remove the 2 7/32" bolts holding the optimal trim item on the column and rerelocate the trim.Rerelocate the single 7/32" bolt underneath the peak trim item.
*
Figure 12. Rerelocate the 2 bottom bolts from the column.
*
Figure 13. Rerelocate the top bolt from the column.Push the tab on the top/side of the turn signal switch and lift it directly up.Disconnect the 3 wiring harnesses linked to the turn signal switch.
*
Figure 14. Push dvery own on the tab and also pull up to release the turn signal switch.
*
Figure 15. Disconnect the wiring harnesses.

See more: Move Variable From Denominator To Numerator S, Moving Variables Around

Step 4 – Install brand-new revolve signal switch

Use a pick to rerelocate the spring from the old revolve signal switch and area it in the new switch (if your brand-new one does not come with a spring). Connect the harnesses and also slide the new switch in place. Relocation the top bolt and also bottom bolts on the column, lift up on the column, then rearea the optimal panel and also reinstall the two bolts on the bottom. Reinstall the bottom panel and also push it in area. Replace the screw on the bottom of the cover. Slide the steering wheel back on so the yellow dot is lined up, reattach the harness, and also reinstall the Torx screw. Make sure the steering wheel is straight, then reconnect the harnesses for the steering wheel horn/airbag and replace the bolt on either side. Push the steering wheel circular covers earlier in location. Reinstall the fusage and panel cover, then reconnect the battery.