vehicle failed to start, discovered starter had actually an open up on the ar windings. Changed starter, no improvement. Haynes hand-operated schematic reflects a starter enable relay in the circuit. Ns cannot find this relay to examine it. It offers the 12 volts come initiate the holding circuit to enable the starter engine to rotate the engine. I require a ar for this relay and also any other suggestions about this problem.


You are watching: 1998 buick lesabre starter relay location

*

Under the left hand the the tool panel, above the instrument panel fuse block. Look simply left of the steering column support and also on a bracket alongside the main wiring conduit. You will have to remove the fuse block cover and also panel. Starter allow RelayBehind left side of dash, left of steering column. This guide can aid as well:https://www.chathamtownfc.net/articles/how-to-replace-a-starter-motorHere is the starter wiring diagrams together well. Inspect out the diagrams (below). Please let us know if you require anything rather to gain the trouble fixed.
*

*

*

*

Engine mechanically problem1998 Buick Lesabre 6 cyl prior Wheel journey Automatic where space the place of every the starter boltes in a 3.8 eng.
begin by removing soil on battery. There are two 10mm screws that organize a plastic cover approximately starter and flywheel area. Eliminate that cover. Then there space two 15mm bolts that host starter come engine block. Eliminate those bolts. Rest starter top top engine cradle carefully and also remove 12volt battery cable and also starter input wire. This guide will assist walk you with the jobhttps://www.chathamtownfc.net/articles/how-to-replace-a-starter-motor please let us recognize if you require anything rather to get the trouble fixed.
Engine mechanically problem1998 Buick Lesabre 6 cyl 2 Wheel journey Automatic plenty of miles yes sir -- I must replace the starter. I"ve got the front end of the auto up on blocks. I deserve to see the starter, but there"s a cross panel that"s in the way.I haven"t disconnected the cables yet. II want to acquire some feedback prior to I starter law anything.I wonder if the 2 bolts that hold it in are on the various other side that the starter. If the s the case, things may have actually just gotten a harder. Many thanksRod --
There need to be two black plastic covers in ~ the former of the starter. Remove them. Castle are organized on v 3 bolts. Remove the starter wires. Remove the two starter bolts.
The solenoid is mounted on optimal of the starter. That"s where the battery cable and also the manage wire affix to the starter.
The starter is ~ above the left next of the engine block under low here is a guide and also a diagrams listed below to assist you adjust the starter engine out.https://www.chathamtownfc.net/articles/how-to-replace-a-starter-motorif the begin is not functioning this guide will helphttps://www.chathamtownfc.net/articles/starter-not-working-repairCheck out the diagrams (Below). Please let us know if you require anything rather to acquire the trouble fixed.Cheers
Hi:First, disconnect the battery. Next, eliminate the wiring to the starter. Finally, unbolt the 2 wires come the starter (Holding starter come the bell housing). The starter will currently come out. Change the new one in the reverse order.Joe
I replaced the starter with attached solenoid. Unfortunately I broke the connector ~ above the tiny wire, not the battery one. Have the right to I just get a copper crimp on ring terminal and crimp it on the finish of the cable? concerned that the piece presented has something important in it?
Yes, you deserve to do what girlfriend suggested. However, make sure you acquire a quality part and replace any kind of covering the initial wire may have actually to remove the possibility of a short.
Engine mechanical problem1997 Buick Lesabre 6 cyl former Wheel journey Automatic procedure to r&r starter


See more: Oxygen, Carbon And Hydrogen Forms How Many Bonds Are Formed By Hydrogen Bonding

1997 Buick LeSabre V6-3.8L VIN KStarter Replacement: Starter motor Mounting

*

remove OR DISCONNECT 1.Negative battery cable. 2.Raise vehicle. 3.Splash shield. 4.Bolts to flywheel investigate cover. 5.Flywheel inspection cover. 6.Starter wiring. 7.Starter mounting bolts. 8.Starter.INSTALL OR connect NOTICE: prior to installing starter motor to engine, the sure electric terminals are secure through tightening nuts alongside cap top top solenoid battery terminal and also on the SD-255 "S" terminal. If these terminals are not chop in solenoid cap, the cap may be damaged during installation of electrical connections and cause starter to loss later.1.Starter. 2.Starter mounting bolts. Tighten *Bolts come 43 N.m (32 lb. Ft.) .3.Starter wiring. Tighten *Nut on solenoid battery terminal come 16 N.m (12 lb. Ft.) . *Nut on "S" terminal come 2.5 N.m (22 lb. In.) .4.Flywheel inspection cover. Tighten *Bolts to 7 N.m (62 lb. In.) .5.Splash shield. 6.Lower vehicle. 7.Negative battery cable. Tighten *Cable bolt come 15 N.m (11 lb. Ft.) .